banner



How Many S9 Miners Can I Run With A 800a Service

BITMAIN logo AntMiner logo S9 SE Server
Installation Guide
Certificate Version 1.0

© Copyright Bitmaintech Pte. Ltd. 2007 – 2019. All rights reserved.
Bitmaintech Pte. Ltd. (Bitmain) reserves the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue whatever production or service without detect.
Customers should obtain the latest relevant information before placing orders and should verify that such data is current and complete. All products are sold subject to Bitmain's terms and conditions of auction supplied at the time of order acknowledgment.
Bitmain warrants the performance of its products to the specifications applicable at the fourth dimension of sale in accordance with Bitmain'southward standard warranty. Testing and other quality control techniques are used to the extent Bitmain deems necessary to support this warranty. Except where mandated by authorities requirements, testing of all parameters of each production is not necessarily performed.
Bitmain assumes no liability for tertiary‐party applications assistance. Customers are responsible for their products and applications using Bitmain components. To minimize the risks associated with customer products and applications, customers should provide acceptable pattern and operating safeguards. Bitmain does not warrant or represent that any license, either express or implied, is granted under any Bitmain patent right, copyright or other Bitmain intellectual belongings right relating to any combination, machine, or process in which Bitmain products or services are used. Information published past Bitmain regarding third‐party products or services does not constitute a license from Bitmain to utilize such products or services or a warranty or endorsement thereof. Use of such data may require a license from a third party nether the patents or other intellectual property of the tertiary party, or a license from Bitmain under the patents or other intellectual property of Bitmain.
Resale of Bitmain products or services with statements unlike from or beyond the parameters stated by Bitmain for that production or service voids all express and whatever implied warranties for the associated Bitmain product or service and is an unfair and deceptive concern practice. Bitmain is not responsible or liable for any such statements.
All company and brand products and service names are trademarks or registered trademarks of their respective holders.
All text and figures included in this publication are the sectional property of Bitmaintech Pte. Ltd. (Bitmain), and may not be copied, reproduced, or used in whatsoever manner without the express written permission of Bitmain. Data in this document is discipline to alter without notice and does not correspond a commitment on the part of Bitmain. Although the information in this certificate has been carefully reviewed, Bitmain does not warrant information technology to be complimentary of errors or omissions. Bitmain reserves the right to brand corrections, updates, revisions or changes to the information in this document.
Bitmaintech Pte.Ltd.
Tel:+86‐400‐890‐8855
www.bitmain.com

Overview

The S9 SE server is Bitmain's newest version in the S9 SE server series. All S9 SE servers are tested and configured prior to shipping to ensure piece of cake setup.

BITMAIN AntMiner S9 SE Server - Overview instructions

  1. You lot must provide your own ATX ability supply.
  2. Please refer to the layout in a higher place to identify your goods in usage in case of any damage.
S9 SE Server Components

The main components and controller front panel of S9 SE server are shown in the following figure:BITMAIN AntMiner S9 SE Server - Server Components

Connecting to the Power Supply
  1. Remove the screw at the position indicated past A with a cross screwdriver.BITMAIN AntMiner S9 SE Server - Power Supply 1
  2. Lift the upper cover of the control board upward at the management indicated past the arrow shown in the figure and then pull it at the upper rear direct ion.BITMAIN AntMiner S9 SE Server - Power Supply 2
  3. The position and proper name of the socket are shown in the figure below later on removing the upper cover of the control board.BITMAIN AntMiner S9 SE Server - Power Supply 3
    No. Item Quantity
    1 FanSocket ii
    2 Chief Control PSU Socket 1
    3 Dashboard Point Socket 3
    four Dashboard PSU Socket 9
    5 Primary Control Board PSU Socket 4
  4. Connecting the external power supply to the respective socket of the server and the bind the cable sabbatum the position indicated by B.BITMAIN AntMiner S9 SE Server - Power Supply 4
  5. Put the upper cover of the command board back in place and fix the spiral at the position indicated past A. Note that the bundled cables shall be placed into the U‐shaped hole.BITMAIN AntMiner S9 SE Server - Power Supply 5

warning 2 Alert: Free energy Hazards!
Please be sure to follow the transmission for installation.
Risk of injury due to energy hazard exists inside.
Be sure to close the metal cover before powering on the equipment, otherwise, there is a risk of injury.
Be sure to employ an external ability supply that was approved according to IEC 60950‐1:2005 + A1 + A2 or IEC 62368‐i:2014. The external ability supply shall provide SELV output and be evaluated.

Specifications

Model No.: 120‐G
Version: S9 SE

Product Glance Value
Crypto Algorithm/Coins SHA256/BTC/BCH
Hashrate, TH/s 16
Reference ability efficiency on wall @25°C, J/TH fourscore
Hardware Configuration
Quantity of hash chips 180
Quantity of hash boards 3
Networking connectedness mode RJ45 ethernet 10/100M
Server Size (Length*Width*Height, due west/o package), mm 321.iii*129.half-dozen*200
Cyberspace weight, kg 4.56
Noise, dBA @25°C(1‐1) 76
Environment Requirements
Functioning temperature,°C 0 25 xl
Storage temperature,°C ‐xl 25 85
Operation humidity, RH v% 0 95%

Notes: (1‐1) Max condition: Fan is under max RPM(rotation per minute).
The parameter table in a higher place is for reference only, full specifications of the S9 SE server volition exist updated subsequently.

Setting Upward the Server

To set up up the server:

instructions The file IPReporter.zip is supported by Microsoft Windows only.

  1. Go to the following site: https://shop.bitmain.com/support.htm?pid=00720160906053730999PVD2K0vz0693
  2. Download the following file: IPReporter.cipher.
  3. Extract the file.
    instructions The default DHCP network protocol distributes IP addresses automatically.
  4. Correct‐click IPReporter.exe and run it as Ambassador.
  5. Select i of the following options:
    • Shelf, Stride, Position – suitable for subcontract servers to mark the location of the servers.
    • Default – suitable for home servers.
  6. Click Starting time.BITMAIN AntMiner S9 SE Server -Start
  7. On the controller board, click the IP Report button. Hold it downwardly until information technology beeps (about 5 seconds).BITMAIN AntMiner S9 SE Server -Setting Up
    The IP address will be displayed in a window on your calculator screen.BITMAIN AntMiner S9 SE Server - computer screen
  8. In your web browser, enter the IP accost provided.
  9. Go on to login using root for both the username and countersign.
  10. In the Network section, y'all can assign a DHCP IP address (optional).
  11. Click Save & Apply.BITMAIN AntMiner S9 SE Server - Apply

Configuring the Server

Setting Up the Puddle
To configure the server:

  1. Click General Settings.BITMAIN AntMiner S9 SE Server - General Settings
  2. Gear up the options co-ordinate to the following table:
    Selection Description
    Pool URL Enter the URL of your desired pool.
    instructions The S9 SE server tin exist set with three mining pools, with decreasing priority from the offset puddle (pool 1) to the third pool (pool 3).
    The pools with low priority will only be used if all higher priority pools are offline.
    Worker Your worker ID on the selected pool.
    Countersign The password for your selected worker.
  3. Click Save & Apply to salvage and restart the server.

Monitoring Your server

To check the operating condition of your server:

  1. Click the status marked below.BITMAIN AntMiner S9 SE Server - status marked instructions Note: The S9 SE server is with automated frequency. The firmware volition stop running when the Temp(PCB) reaches 85℃ or the Temp(Chips) reaches to 105℃, there will exist an error message "Fatal Fault:
    Temperature is besides high!" shown in the bottom of the kernel log page.
  2. Monitor your server according to the descriptions in the following table:
Choice Clarification
ASIC# A number of fries were detected in the chain.
Frequency ASIC frequency setting.
GH/S(RT) Hash rate of each hash lath (GH/s).
Temp(PCB) The temperature of each hash board (°C). (Practical but to the server with stock-still frequency).
Temp(Fleck) The temperature of the chips on each hash board (°C).
ASIC status 1 of the post-obit statuses will appear:
● O ‐ indicates OK
● X ‐ indicates error
● ‐ ‐ indicates dead

Administering Your Server

Checking Your Firmware Version

To check your firmware version:

  1. In System, click the overview tab.
  2. File System Version displays the engagement of the firmware your server uses. In the example below, the server is using firm version 20190616.BITMAIN AntMiner S9 SE Server - status marked
Upgrading Your System

instructions Make sure that the S9 SE server remains powered during the upgrade process. If power fails before the upgrade is completed, you will demand to render it to Bitmain for repair.
To upgrade the server's firmware:

  1. In the System, click Upgrade.BITMAIN AntMiner S9 SE Server -Upgrade
  2. For Keep Settings:
    • Select the check box to keep your electric current settings (default).
    • Clear the check box to reset the server to default settings.
  3. Click the (Browse) button and navigate to the upgrade file. Select the upgrade file, then click Flash image. A message appears notifying you if the S9 SE firmware can be upgraded and if yes, will then proceed to wink the image.
  4. When the upgrade is completed, the following bulletin appears:BITMAIN AntMiner S9 SE Server -message appears
  5. Click one of the following options:
    • Reboot ‐ to restart the server with the new firmware.
    •Go Dorsum ‐ to continue mining with the current firmware. The server volition load the new firmware next time when it is restarted.
Modifying Your Password

To change your login password:

  1. In System, click the Administration tab.
  2. Prepare your new password, and so click Save & Apply.BITMAIN AntMiner S9 SE Server -Save
Restoring Initial Settings

To restore your initial settings

  1. Turnontheserverandletitrunfor5minutes.
  2. On the controller front end panel, printing and hold the Reset button for 10 seconds.
    instructions Resetting your server volition reboot information technology and restore its default settings. The red LED will automatically flash once every fifteen seconds if the reset is operated successfully.

Ezoic

Environmental Requirements
Please run your server in accordance with the post-obit requirements

Basic Environmental Requirements:

Climatic Conditions:
Description Requirement
Operating Temperature 0‐40˚C
Operating Humidity ten‐90%RH (not‐condensing)
Storage Temperature ‐20‐70℃
Storage Humidity 5‐95%RH(non‐condensing)
Altitude <2000m
Site Requirements of the Server Running Room:

Please keep the server running room away from industrial pollution sources:
For heavy pollution sources such equally smelters and coal mines, the altitude should be more than 5km.
For moderate pollution sources such as chemical industries, rubber, and electroplating industries, the altitude should be more than than 3.7km.
For light pollution sources such as food factories and leather processing factories, the altitude should be more than 2km.
If unavoidable, the site should be called in the perennial upwind direction of the pollution source.
Please do not set your location within 3.7km from the seaside or the common salt lake. If unavoidable, it should be built as closed as possible, equipped with ac for cooling.

Electromagnetic Environmental Conditions:

Please keep your site away from transformers, loftier‐voltage cables, transmission lines, and high‐current equipment, for instance, at that place should exist no high‐power Air-conditioning transformers (>10KA) inside twenty meters, and no high‐voltage power lines within 50 meters.
Please proceed your site away from high‐ability radio transmitters, for instance, there should exist no high‐ability radio transmitters (>1500W) within 100 meters.

Other Environmental Requirements:

The server running room shall be free of explosive, conductive, magnetically conductive, and corrosive dust. The requirements of mechanical active substances are shown below:

Requirements of Mechanical Active Substances
Mechanical Active Substance Requirement
Sand <= 30mg/m3
Dust (suspended) <= 0.2mg/m3
Dust (deposited) <=1.5mg/m2h
Requirements of Corrosive Gas
Corrosive Gas Unit of measurement Concentration
H2S ppb <3
SO2 ppb <ten
Cl2 ppb <ane
NO2 ppb <50
HF ppb <1
NH3 ppb <500
O3 ppb <2
Note: ppb (part per billion) refers to the unit of concentration, 1ppb stands for the book ratio of office per billion.

Regulations:
FCC Find (FOR FCC CERTIFIED MODELS):
This device complies with part 15 of the FCC Rules. Operation is subject to the following two atmospheric condition: (i) This device may not cause harmful interference, and (2) this device must take any interference received, including interference that may cause undesired functioning.
Note:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to function fifteen of the FCC
Rules. These limits are designed to provide reasonable protection confronting harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and tin can radiate radio frequency energy and, if not installed and used in accordance with the education manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is probable to cause harmful interference in which case the user will be required to correct the interference at his ain expense.
Eu WEEE: Disposal of Waste Equipment past Users in Private Household in the European Union
Dustbin IconThis symbol on the product or on its packaging indicates that this production must non exist disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste product equipment by handing information technology over to a designated collection betoken for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will assist to conserve natural resources and ensure that information technology is recycled in a manner that protects man health and the surround. For more information about where you can drib off your waste product equipment for recycling, please contact your local city part, your household waste matter disposal service or the shop where you purchased the product.

Documents / Resources

Source: https://manuals.plus/bitmain/antminer-s9-se-server-manual

Posted by: rachalbeenarile.blogspot.com

0 Response to "How Many S9 Miners Can I Run With A 800a Service"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel